banner



How To Take Broken Glass Out Of A Window

The trickiest function of replacing broken glass panes in woods-frame windows is getting replacement glass that's sized exactly right. To replace a cleaved glass pane in a wood window, you need to measure the precise length and width of the grooves in which the pane will fit.

Have the new drinking glass cut so it measures i/8 inch shorter than the verbal groove dimensions in both the length and width. This creates a 1/xvi-inch gap on each side betwixt the edges of the pane and the rabbet groove. The gap provides room for the glass to aggrandize when the weather changes.

In addition to the replacement glass pane, you'll need: latex glazing putty; metal glazing points; pliers; a rut gun; flexible putty knife; 1- or 2-inch, stiff, steel, putty pocketknife; and a flathead screwdriver.

Also bank check out these other articles on replacing broken window panes in: steel-casement windows; sliding-sash windows; and metal tempest windows.

Employ the pliers to remove all of the drinking glass shards.

Use the pliers to remove all of the glass shards.

When you work with broken glass, wear safe goggles as well as gloves; small chips of drinking glass can cause permanent heart impairment.

Use the estrus gun to warm the former putty; and then scrape it away with a putty knife.

Use the heat gun to warm the old putty; and then scrape it away with a putty knife.

If the putty doesn't elevator off easily, apply more heat and attempt once again. Exist patient — the putty around really one-time windows is as hard equally concrete, just information technology volition soften.

Don't chisel out the old putty — you might wreck the window. The putty will soften with enough heat and time.

Utilise a putty knife or the tip of a screwdriver to remove the one-time glazing points.

Use a putty knife or the tip of a screwdriver to remove the old glazing points.

The points will be buried under the old putty.

Clean and inspect the rabbet groove.

Clean and inspect the rabbet groove.

Ensure that no glazing putty, glass shards, or glazing points remain.

Apply a bead of putty on the glass side of the rabbet groove.

Apply a bead of putty on the glass side of the rabbet groove.

Squeeze out a 1⁄xvi-inch bead of putty between the edge of the drinking glass and the window frame.

Gently press downwards the drinking glass at the edges to embed the glass into the putty.

Gently press down the glass at the edges to embed the glass into the putty.

Allow the putty to spread out and grade a moisture seal on the inside of the window between the glass and sash.

Position the new pane in the rabbets.

Position the new pane in the rabbets.

Shift the pane until you accept a one/xvi-inch gap betwixt the pane and sash on all four sides.

Place at least two new glazing points in each section of the window sash surrounding the new glass.

Place at least two new glazing points in each section of the window sash surrounding the new glass.

Space the points evenly effectually the perimeter, about six inches apart.

Apply the flat side of a putty knife to push one corner of each triangular glazing point into the wood sash.

Use the flat side of a putty knife to push one corner of each triangular glazing point into the wood sash.

You can use a screwdriver blade instead of a putty knife.

Form a ane/2-inch-thick rope of putty and press the length along all iv sides of the glass.

Form a 1/2-inch-thick rope of putty and press the length along all four sides of the glass.

Roll a glob of putty between your blank easily to form the rope.

Smooth the glazing putty and scrape abroad the backlog.

Smooth the glazing putty and scrape away the excess.

Hold the putty knife at a 45-degree angle, press, and shine the glazing putty against the drinking glass and sash.

Later on the putty dries completely, repaint the putty and repaired surface area.

After the putty dries completely, repaint the putty and repaired area.

Don't mask off the glass before repainting. The paint will help form a moisture seal between the drinking glass pane and the sash. And then, allow the pigment to overlap about 1/viii inch onto the drinking glass.

Nigh This Article

About the book authors:

Gary Hedstrom is a self-taught repair main with feel in carpentry, plumbing, appliance repair, and more than. He has synthetic two houses with his wife, Peg. Peg Hedstrom is a self-taught repair master with experience in carpentry, plumbing, appliance repair, and more. She has constructed two houses with her husband, Gary. Judy Ondrla Tremore is a writer and editor for various newspapers and magazines.

This article tin be constitute in the category:

  • Windows ,

Source: https://www.dummies.com/article/home-auto-hobbies/home-improvement-appliances/windows-home-improvement-appliances/how-to-replace-a-broken-glass-pane-in-a-wood-frame-window-206792/

Posted by: lopezprolent.blogspot.com

0 Response to "How To Take Broken Glass Out Of A Window"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel